How to Install Drop Ceiling in 2022

Compared to drywall, the many benefits of a drop ceiling are numerous. Drop ceilings are inexpensive, simple to install, and convenient for later access to ductwork and wiring. First, you’ll need to install a grid system of runners to support your ceiling tiles. How to install drop ceiling? Once the grid is in place, you’re ready to start laying the tiles for your new ceiling!

How to Install Drop Ceiling

You should know how long each of your room’s walls is. Use a tape measure to determine how long each division in the room will be once the ceiling is installed. Record your room’s dimensions 2–3 inches (5.1–7.6 cm) up from the top of the wall, so you have them handy later. Measuring the length and width of a rectangular room is easier than a square one because they are the same size.

Drop ceiling installation:

Measure the distance from the top of your walls to a horizontal line of 4–6 inches (10–15 centimeters). Allow at least 4–6 in (10–15 cm) of space between the top of your wall and your line for fixtures and the installation of your tiles. Draw a straight line around your room with a pencil and a 4-foot (1.2-meter) level. 

There is an easier way: use a chalk line and snap it. To transfer the chalk line’s line onto the drywall, you must photograph it against your wall while holding the string in place.

If you intend to use a large fluorescent light panel, you should make your line 6 in (15 cm).

Wall angle cuts can be made with tin snips

Tiles and runners are held in place by long L-shaped pieces known as wall angles. The length of most wall angles is 8–12 ft (2.4–3.7 m), so use your tin snips to cut them down to the proper size for your project’s walls.

The wall angles on those walls should be cut 12 inches (1.3 cm) longer than your measurements if you have a corner that protrudes from your wall.

Using a 45-degree angle, cut the bottommost wall angle of the wall runner for a mitered finish.

Read also: Five Best Modern Computer Desk

Wall angles:

Be sure to line up the ends of any walls that are longer than the wall angles. Assemble the wall angles by screwing them into the wall studs along the drawn line. How to install drop ceiling? Mark the locations of the studs on your walls using a pencil and a stud finder. Align the wall angle’s apex with the line you drew on the wall’s surface. Use 1 14 in (3.2 cm) screws and an electric screwdriver to fasten your wall angles to the studs.

As you install your wall angles, make sure they are level.

Perpendicular to the joists, cut the main runners to fit the length of your room. The weight of your ceiling will fall primarily on the main runners. How to install drop ceiling? Your ceiling’s wooden joists should be perpendicular to the size of your room. Tin snips can be used to cut the runners to the proper length. It’s best to use clips on both ends of the main runner if your room is greater in size than the length of a single piece.

How to install drop ceiling & Ceilings installation?

Use a chalk line or string across your room every four feet to keep track of your measurements (1.2 m). How to install drop ceiling? Using a chalk line, draw a straight line from one end of your room to the other. To leave a mark on the joists, snap the chalk line. Make a new line on your ceiling at about 1.2 m (4 ft). Keep going until you get to the other side of your room.

Make a chalk line on your ceiling by tying the string tightly across it.

Every third joist along the line should have an eyelet installed. Using eyelet screws, you can hang your main runner by running wires through the holes on the end of them. An electric screwdriver fitted with a lag bit is the perfect tool for inserting an eyelet. Along each chalk or string line, begin installing your eyelets three joists away from the wall. Every third joist, insert an eyelet.

Hardware stores sell LED-illuminated screws for your convenience.

Each eyelet can be pierced with a piece of wire. Cut a 20–25 cm (8–10 in) piece of 16-gauge wire for each eyelet. Feed the wire through the eyelet and bend it until it points downward with a pair of pliers.

How to install ceiling tiles?

Using the wires, hang up the main runners. Your main runners should be perpendicular to your joints when held up like this. A circular slot on the runners allows you to feed the other end of the wire and bend it with your hands. Keep the cables secure by twisting them around themselves at least three times. Check the level of your joists before adding more wires. If one wire is higher than the other, the bend should be adjusted.

Basement drop ceiling lighting:

Clip the secondary runners into place to run parallel to your primary ones. Locate the slots on the main runners (0.61 m) every two feet. Assemble four-foot runners and feed them into the main runners’ spaces. 

Cut holes in the tiles:

Before installing any lighting or ductwork, cut holes in the tiles. Check your ceiling for areas where you’ll need to cut openings for ducts or lighting fixtures. One of your tiles can serve as a template for drawing on the back of a duct or light fixture’s dimensions. Use a utility knife to cut out the desired shape from the tile carefully. It is not necessary to cut any conditions from the tiles if a full-panel fluorescent light fixture is installed.

Ceiling grid installation:

Using a utility knife, cut any edge tiles to the correct size. Your room will likely have some areas where full-sized tiles will not fit. How to install drop ceiling? The tile’s grid opening should be measured, and the additional 3/8″ (0.95 cm) should be added. Using a utility knife, cut the tile to the correct size based on that measurement.

Suspended ceiling installer:

Cutting your tiles by hand will produce a lot of dust, so stay away from power tools.

In any cut edge of your tiles, cut out a 3/8 in (0.95 cm) flange. When installing the tile in your ceiling, the flanges rest on the runners and add depth to the tile. Draw a line with a pencil 38 in (0.95 cm) from any edge that does not have a flange. 


Installing a drop ceiling yourself can save you time and money in the long run. Prepare for your installation with these helpful hints, safety reminders, a tool list, and step-by-step instructions.

Read further: Five Best Handbags for School and Collages

Leave a Reply

Your email address will not be published.